Floss Field.
SearchSaved
All crafts

Crochet guide

Crochet edges on knitting

To crochet an edge on knitting, work one row of single crochet (double crochet in the United Kingdom) into the knitted edge with the right side facing you. Put one stitch into each knitted stitch along the top and the bottom, fewer stitches than rows along the sides, and three stitches into each corner.

On this page 10 parts
  1. What a crochet edge does for knitting
  2. What you need
  3. Where the hook goes
  4. How many stitches along a side
  5. A border on a knitted blanket
  6. A crochet bind-off
  7. Joining knitted pieces with crochet
  8. Crochet on a knitted hat, cuff or neckline
  9. What changes when one piece mixes both
  10. Where to go next

What a crochet edge does for knitting

A row of single crochet gives a knitted piece a firm, even edge. It can be the whole finish, or the base for a fancier border. Crochet has less stretch than knitting, so a row of it also steadies an edge or a seam that stretches too much.

Stitch names on this page are United States terms, with the United Kingdom name in brackets where it differs.

Single crochet is also one of the edges knitters use to keep stockinette stitch from rolling. If one round does not hold the edge flat, work more rounds.

What you need

  • A hook close in size to the knitting needles. Hooks and needles are both sized in millimeters. The knitting needle to crochet hook chart sets the sizes side by side. If the new edge pulls tight or waves, change the hook size.
  • Yarn. The yarn of the piece, or another of the same weight.

Where the hook goes

Work with the right side of the knitting facing you. Each edge of a knitted piece takes the hook in its own place.

  • The bound-off edge and the cast-on edge. Push the hook through the middle of a knitted stitch just under the edge, going in at the front of the fabric and out at the back. Work one single crochet into each knitted stitch.
  • The side edges. These are the ends of the rows. Put the hook in one whole stitch from the edge.
  • The corners. Work three single crochet into the corner stitch, so that the border can turn and still lie flat.

How many stitches along a side

A knitted stitch is wider than it is tall, so a side has more rows than it needs crochet stitches. Knitters who pick up stitches along a side often take 3 stitches for every 4 rows. The same spacing is a starting point for single crochet: 3 stitches for every 4 rows, or 2 for every 3.

Which one lies flat depends on your knitting and on your crochet. Work a short stretch, lay the piece down and look.

  • If the edge waves, it has too many stitches.
  • If the edge draws the knitting in, it has too few, or they are too tight.

Count the stitches on each side. Two sides of the same length get the same number. Picking up stitches shows the same spacing and checking on a crocheted edge.

A border on a knitted blanket

  1. Join the yarn on the bound-off edge.
  2. Work one single crochet into each knitted stitch as far as the corner.
  3. Work three single crochet into the corner stitch.
  4. Work down the side, spacing the stitches as above.
  5. Go on round the cast-on edge and up the other side, with three stitches in each corner.
  6. Join the last stitch to the first with a slip stitch. Fasten off, or go on with the next round.

This plain round is the foundation for the rest. Reverse single crochet, also called crab stitch, makes a corded edge over it. Picots and shells make a lacier one. Adding a border to a blanket covers the rounds that follow.

A crochet bind-off

A crochet hook can also bind off knitting that is still on the needle. It leaves a chain along the edge, as a standard bind-off does.

  1. Hold the needle with the stitches in your left hand and the hook in your right.
  2. Put the hook into the first stitch on the needle. Catch the working yarn and pull it through. Let the stitch drop off the needle. One loop is on the hook.
  3. Do the same in the next stitch. Two loops are on the hook.
  4. Pull one loop through the other, as in a crochet slip stitch. One loop is left on the hook.
  5. Repeat steps 3 and 4 to the end. Cut the yarn. Pull the end through the loop that is left.

Keep the loops loose. A tight chain takes the stretch out of the edge.

Joining knitted pieces with crochet

Knitted squares and panels can be joined with a hook as crocheted ones are.

  • A slip stitch seam is worked through both pieces held together. It is firm, and it keeps a seam from stretching.
  • A single crochet seam is worked the same way. It leaves a ridge, so it is used where the ridge is wanted as a detail.
  • A round of single crochet first. Edging each square with single crochet gives it a smoother edge to join through.

Joining squares and joining and seaming pieces teach the joins.

Crochet on a knitted hat, cuff or neckline

The edge of a hat, a cuff, a sock top or a neckline is a cast-on or bound-off edge like any other. A round of single crochet goes into it in the same way, one stitch into each knitted stitch. Crochet does not stretch as knitting does, so keep the stitches loose on an edge that has to stretch to go on.

What changes when one piece mixes both

  • Stretch. Knitted fabric is stretchier than crochet. A crochet edge will not give as much as the knitting beside it.
  • Thickness. Crochet fabric is thicker and denser than knitting in the same yarn.
  • Yarn. For the same area, crochet takes more yarn than knitting does. Allow for it when a border is added to a finished piece.
  • Size. A knitted stitch and a crochet stitch are not the same size, even in the same yarn. That is why the spacing along a side is found by trying it, not by counting one stitch for each row.

Crochet and knitting compared has more on how the two fabrics differ.

Where to go next